Admissions open for classroom and online training. ENROLL NOW.
Geometric Dimensioning & Tolerancing (GD&T Training)
Instructor-Led Online Training Program on “Geometric Dimensioning & Tolerancing (GD&T Training)” by Industrial Expert
Duration:Intermediate Course- 2 Days, Advanced Course: 3 Days
Schedule: Multiple batches are available in May, June & July, 2021
Mode of Training: Instructor-Led Online Training
Course Contents
| Intermediate Course: | Advanced Course: |
|---|---|
| Introduction, History & Purpose of Geometric Dimensioning & Tolerancing (GD&T) | Introduction, History & Purpose of Geometric Dimensioning & Tolerancing (GD&T) |
| Ambiguity & Shortcomings of Co-ordinate Measuring System | Ambiguity & Shortcomings of Co-ordinate Measuring System |
| Benefits of Circular tolerance zone over Square tolerance zone | Benefits of Circular tolerance zone over Square tolerance zone |
| Exercise-1 on conversion from Sqaure Tol zone to Round Tol zone for Positional Tolerance | Exercise-1 on conversion from Sqaure Tol zone to Round Tol zone for Positional Tolerance |
| Basics of GD&T terminology e.g. MMC. LMC. RFS, Bonus Tolerance, WCB, RFS, Control Frame | Basics of GD&T terminology e.g. MMC. LMC. RFS, Bonus Tolerance, WCB, RFS, Control Frame |
| Exercise-2 Identify MMC/LMC sizea on Shaft & Hole | Exercise-2 Identify MMC/LMC sizea on Shaft & Hole |
| Exercise-3 on calculation of Bonus Tolerance (for Postion Tol) | Exercise-3 on calculation of Bonus Tolerance (for Postion Tol) |
| Size limits, Hole base System, Fits | Size limits, Hole base System, Fits |
| Exercise-4 Wall weak calculation for LMC | Exercise-4 Wall weak calculation for LMC |
| Rule #1 | Rule #1 |
| Rule #2 | Rule #2 |
| Form Controls (Straightness, Flatness, Circularity, Cylindricity) – Definition, Application & Measurement | Form Controls (Straightness, Flatness, Circularity, Cylindricity) – Definition, Application & Measurement |
| Exercise-5 OK/Not OK Part after inspection for Circularity | Exercise-5 OK/Not OK Part after inspection for Circularity |
| Exercise-6 Identify Non conformity of Control Frame | Exercise-6 Identify Non conformity of Control Frame |
| Datums (Primary, Secondary, Tertiary), Simultaneous datums, 3-2-1 Principle | Datums (Primary, Secondary, Tertiary), Simultaneous datums, 3-2-1 Principle |
| Orientation Controls (Angularity, Perpendicularity, Parallelism) – Definition, Application & Measurement | Orientation Controls (Angularity, Perpendicularity, Parallelism) – Definition, Application & Measurement |
| Exercise-7 Identify Non conformity of Control Frame | Exercise-7 Identify Non conformity of Control Frame |
| When Tol zone will have diameter symbol & when it is not specified in Control Frame? | When Tol zone will have diameter symbol & when it is not specified in Control Frame? |
| Can we interchange primary & secondary datums? Exercise-8 Calculation of Bonus for other than position tol | Can we interchange primary & secondary datums? Exercise-8 Calculation of Bonus for other than position tol |
| Exercise-9 Identify Non conformity of Control Frame | Exercise-9 Identify Non conformity of Control Frame |
| Location Controls (Position, Concentricity, Symmetry) – Definition, Application & Measurement | Location Controls (Position, Concentricity, Symmetry) – Definition, Application & Measurement |
| Exercise-10 How to design Postion Tolerance based on mating part dimns? | Exercise-10 How to design Postion Tolerance based on mating part dimns? |
| Exercise-11 Ok/Not OK Part after inspection by Layout method | Exercise-11 Ok/Not OK Part after inspection by Layout method |
| How to calculate position tol for fixed fastener & Floating fastener condition? With Exercises-4&5 | How to calculate position tol for fixed fastener & Floating fastener condition? With Exercises-4&5 |
| Exercise-12 Identify Non conformity of Control Frame | Exercise-12 Identify Non conformity of Control Frame |
| Runout Controls (Circular Runout/ Face Runout, Total Runout/ Total Face Runout) – Definition, Application & Measurement | Runout Controls (Circular Runout/ Face Runout, Total Runout/ Total Face Runout) – Definition, Application & Measurement |
| Profile Controls (Line Profile, Surface Profile) – Definition, Application & Measurement | Profile Controls (Line Profile, Surface Profile) – Definition, Application & Measurementtd> |
| When to apply MMC or LMC modifier in Control Frame? | When to apply MMC or LMC modifier in Control Frame? |
| Brief on Functiona Gaging | Brief on Functiona Gaging |
| Exercise-13 How to inspect actual part if postional tol is mentioned in drawing? | Exercise-13 How to inspect actual part if postional tol is mentioned in drawing? |
| Functional Gage: Exercises-14 How to design functional Gage – Gage 1 | |
| Functional Gage: Exercises-15 How to design functional Gage – Gage 2 | |
| Projected Tolerance Zone | |
| Composite Frames in postional tolerance | |
| Amendment in ASME Y14.5 (2018) standard w.r.t. 2009 | |
| Why Concentricity & Symmetry symbols are removed in new standard (2018) | |
| New addition of symbols | |
| How to analyse assembly requirement and apply controls? Exercises-16 Apply GD&T, based on assy requirements | |
| How errors in Part Drawing increases cost in manufacturing process. | |
| Case Study & Query Resolution |
Payment Mode: To be paid 100% advance
Direct Bank Account Transfer:
Account: IFS Academy
Bank and Branch: Axis Bank Ltd., Kothrud Branch, Pune-411038
Account Number: 104010200009058
Account Type: Current
Branch Code: 000104
IFSC Code: UTIB0000104
RTGS Code: Same as above
MICR Code: 411211004
Note: After successful transaction, you are requested to send following details to training@ifsacademy.org
Name of the Student:
Course Title:
Amount (Rs./-):
Transaction ID:
Admission / Registration Procedure:
Students are requested to complete their admission / registration formalities and pay the course fees by clicking on the Apply Now button given below.
